|
|
|
|
|
|
|
|
|
|
|
|
|
|
Molded of tough, high quality plastic with shockproof thickness for safe handling protection.
|
For a secure connection between ground wire and ground rod. Heavy-duty construction. Made of aluminum. Will not rust. For use with 5/8 in and larger ground rods. 1 clamp/Pack.
|
Our Zareba? high-tensile, three-hole twisting tool is an essential tool for bending or twisting high tensile wire, poly spacer clips or for twisting T-post or spacer clips to fasten wire on to posts. Use with up to 8 ga wire.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
When planning your fence, there are several things you should consider. Among these things are placement of the gate and the type of gate handle to use. Your electric fence gate, if possible, should be placed at corners instead of in the middle of the fence. This extremely sturdy Fi-Shock? rubber gate handle is virtually indestructible and will not crack in cold weather.
|
Used to tighten high-tensile wire. Under compression, it automatically feeds into cog reel.
|
Use Zareba? 5 in galvanized brace pins to attach horizontal brace posts to upright brace posts in corner and brace post assemblies. These 5 in brace pins are to be used in anchor posts. They fit 3/8 in hole for easy installation and they're class III galvanized for rust resistance and long life.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Stainless steel spring clip for 3/8 in and 1/2 in fiberglass rod posts. Will not rust or corrode. Safely and securely attach electrified wire or poly wire to fiberglass or rod posts. 20 clips/Bag.
|
Our Zareba? electric fence tester has a light that indicates the current flow through fence wire. It's molded of high-impact ABS. Have peace of mind knowing your fence wire current is flowing properly, securing your livestock and other animals.
|
Add visibility to your electric fence with these Zareba? electric fence warning signs. These signs make people aware of the electrified fence. Low cost and easy to install. Many county laws require electric fence warning signs every 250 ft.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Our Zareba? electric fence wire tap electrically connects one fence wire to the next or hooks up wire to fence wire. It fits 12-1/2 to 16 ga wire. Crimping tool required; crimp twice for a secure connection.
|
Use our Zareba? 10 in galvanized brace pins to attach horizontal brace posts to upright brace posts in corner and brace post assemblies. These 10 in brace pins are to be used in vertical brace posts. They fit 3/8 in hole for easy installation and they're class III galvanized for rust resistance and long life.
|
Insulating grip is soft and flexible with safety flanges for extra shock protection. Unique fastening plate ensures a secure wire connection. Will not break, crack or chip. Steel components are plated to resist rust.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Fi-Shock? in-line strainer handle attaches to any of the Fi-Shock? heavy-duty in-line strainers (model 400-399) you have installed around your fence. With the handle, you can quickly and easily ratchet up the tension on your electric fence wires.
|
Our Zareba? electric fence cut-out switch makes it possible to disconnect the bottom live wire when the grass or snow gets too high. We created our high-quality cut-out switch for that purpose. Use the Zareba? Cut-out switch to switch off selected electric wires on a fence. The handle protects contacts.
|
Used to indicate tension of wire. One inch of compression equals 150 lb of pull. Use one in conjunction with in-line strainer for each leg of fence. Electroplated to deter rust.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Zareba? multi-light electric fence tester makes it easy to measure the amount of voltage in your electric fence. Our electric fence tester measures the voltage drop between points along an electric fence. The lights on our tester are calibrated to glow from 600 to 5500 V.
|
Our Zareba? wood post screw-in gate anchor is designed for wood posts. It can be used with all fence wire, including high tensile.
|
Is your charger worn out or not working at its full capacity. This 4 V replacement battery will get your charger back in ideal working order. This replacement battery is designed for use with ESP2M-FS, ESP2M-Z, SS-440 and SS-740 chargers. Most chargers can hold a charge long after they have been unplugged or disconnected from the battery. An unplugged charger can still shock you. The consumer assumes all risk when repairing or utilizing a charger that has been "repaired" or modified. In addition, once the charger has been opened all warranties are null and void and state of federal inspections and approvals are terminated.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Our Zareba? 16 ft spring gate kit hangs neatly on the gate post when it's recoiled. Highly visible, this spring gate expands up to 16 ft and is electrified when it's stretched across the gate opening.
|
Zareba Fi-Shock Grounding Rod, Copper, 5/8 in Diameter Nominal, 6 ft Length
|
Our Zareba? Electric fence lightning arrester helps protect your fence charger by creating a "path of least resistance," diverting lightning surges to the ground. Install at each corner of the fence for added protection. Connect fence wire to lightning arrester and ground rods using Zareba? 20,000 V underground/hookup wire for all connections.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This insulated T-post gate handle anchor is to be used in conjunction with our fence gate handles. Their screw-in design-type is for T-post gate posts.
|
Use our digital fence line tester to measure fence line and fence charger voltage. This tester combines digital accuracy with ease and convenience. It measures voltage on any type of wire.
|
Our Zareba? Spinning Jenny Wire Dispenser makes payout of coiled high tensile fence wire easy. It can be used for both high tensile and for other fence systems. Made with heavy-duty construction, it holds up to 4000 ft of high tensile wire. This fence wire spinner adjusts to fit 17 to 24 in inside diameter of wire roll and has a built in breaking system. It's easy to assemble and disassemble - no tools required.
|
|
|
