This jamb repair and reinforcement kit is constructed of steel components and comes in a white, paintable powder-coated finish. It features six easy-2-install section plates and two door edge guards and it comes complete with fasteners and step-by-step in.

For use in wood, metal closet or cabinet doors. Adjustable tension, includes fasteners for quick and easy installation.

For use in wood, metal closet or cabinet doors. Adjustable tension, includes fasteners for quick and easy installation.

Hinge mounted to fit all doors. Designed to not touch or damage doors.

Mounts on a door hinge to prevent damage to wall. Easily adjustable by turning adjusting screw. Designed for hollow core doors. Doorstop held in place by hinge pin. Spacer included for thinner hinge pins. Zinc die-cast body, steel adjusting screw, rubber and plastic tips.

Mounts on a door hinge to prevent damage to wall. Easily adjustable by turning adjusting screw. Designed for hollow core doors. Doorstop held in place by hinge pin. Spacer included for thinner hinge pins. Zinc die-cast body, steel adjusting screw, rubber and plastic tips.

Prevents damage to walls. Easy to install, no fasteners - use wrench to screw base into wall. Hole in the end of the plastic tip to help reduce choking hazard. 3 in projection.

Prevents damage to walls. Easy to install, no fasteners - use wrench to screw base into wall. Hole in the end of the plastic tip to help reduce choking hazard. 3 in projection.

Flexible for safety and ease of cleaning. Spring helps prevent wall damage. 3 in projection. Polybagged.

Flexible for safety and ease of cleaning. Spring helps prevent wall damage. 3 in projection. Polybagged.

Secures door to jamb; hardened steel locking rod with die-cast bracket and keeper.

Die-cast painted housing with case-hardened steel bolt. Securely locks door in closed or ventilating position. 2-1/4 in L x 1-1/16 in W. Prevents sliding or lifting of door. Bolt 5/8 in. Includes 1 lock and 2 installation screws. Prefix U on factory number denotes new Prime-Line packaging.

Covers marred doors and allow conversion of 2-3/8 to 2-3/4 in backset or 2-3/4 to 2-3/8 in. Inside diameter of 2-1/8 in, outside diameter of 3-1/2 in. Includes 2 plated covers.

For both in swinging and out swinging doors. Protects against pry bar and other forms of forced entry. Inswing application will require some mortising to jamb.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets or deadbolts.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets or deadbolts. Easy to install.

Surface mounted spring-loaded door closer, works on doors up to 150 lb, non-handed, adjustable tension, UL listed, 1/2 hr fire rated.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets and deadbolts or combination locksets.

This high security door lock is a spring-loaded reinforcement lock that protects against unauthorized entry by preventing lock bumping and lock picking while in the locked position. This lock is designed to withstand 800 lb of force and cannot be opened from the outside.

Solid brass keepers with steel chain secures door while allowing viewing and ventilation. One 5/8 in x 2 in keeper and one 3-5/16 in x 1-3/8 in keeper. Prefix U on factory number denotes new Defender Security packaging.

180 deg viewer. Contains plastic and UL listed glass lenses. Fits 1-3/8 to 2-1/8 in thick wood or metal doors. 9/16 in Dia.

Covers 1/2 to 2-1/8 in holes. Helps maintain entry security. Fits doors up to 1-3/4 in thick.

Fits 5-1/2 in and 6 in hole spacing's on dead latch and deadbolt. Uses six 3 in screws that install on the vertical side of the strike closest to the stop molding. These 3 in screws allow for a strong hold as they drive into the jack stud to help prevent kick-ins.

Plated steel strike is supplied with 3 in long wood screws to allow additional security, by fastening thru jamb into 2 x 4 outer door framing. 1-5/8 in W x 11 in H. Spacing between deadbolt opening and latch opening of 3-5/8 in.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets or deadbolts.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets and deadbolts or combination locksets.

1/8 in thick heavy-gauge steel base allows 3 in screws to anchor to wall stud. Finished cover matches common exterior trim.

1/8 in thick heavy-gauge steel base allows 3 in screws to anchor to wall stud. Finished cover matches common exterior trim.

1/8 in thick heavy-gauge steel base allows 3 in screws to anchor to wall stud. Finished cover matches common exterior trim.

160 deg viewer. Solid brass housing and glass UL listed lenses. 15/32 in bore diameter. Fits 1-3/8 to 2 in thick wood or metal doors. Includes 1 viewer.

200 deg viewer. Solid brass housing and glass UL listed lenses. 9/16 in bore. Fits 1-3/8 to 2-1/8 in thick wood or metal doors. Includes 1 viewer.

Helps prevent wall damage. 2-15/16 in projection. Polybagged.

Dual adjustable ball catch with square corners in satin nickel.

Designed to secure extra large or heavy doors. Large footprint grips on rough or uneven surfaces and large heel holds doors with clearances up to 2 in from floor surface.

The Shepherd Hardware Wall Protectors are used to to protect surfaces from door knob damage or cover existing damage. Self-adhesive and paintable circular disk.

Standard latch strike with 1-5/8 in hole centers. Adjustable tab. Replaces most residential interior and exterior strikes. 1-7/16 in x 2-1/4 in.

Standard T-strike, used on wood or metal jambs with most grade 2 locksets. Includes one strike with two #8 x 1 in Phillips flat head combination screws.

This door guard is constructed from solid brass. It helps to protect your door from forced entry. It can be used on wood or metal doors with mortise or drive-in latches. It can also accommodate key-in knob locksets or deadbolts.

1-1/4 in W x 3-5/8 in L high security deadbolt strike. Includes 1 strike, two 1 in screws and two 3 in long security screws to anchor into the door frame stud.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets and deadbolts or combination locksets.

Covers marred doors and allow conversion of 2-3/8 to 2-3/4 in backset or 2-3/4 to 2-3/8 in. Inside diameter of 2-1/8 in, outside diameter of 3-1/2 in. Includes 2 plated covers.

Standard latch strike with 1-5/8 in hole centers. Adjustable tab. Replaces most residential interior and exterior strikes. 1-7/16 in x 2-1/4 in.

Reinforces and repairs door edge. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates lockset or deadbolt with any backset.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets or deadbolts.

Doorstop is held in place by hinge pin. Helps prevent wall damage. Adjustable to stop door at any angle. Self-adjusting pad makes full contact with door. Polybagged.

160 deg plastic lens viewer, 15/32 in bore diameter. Fits 1-3/8 in thick wood or metal doors. Easy to install.

Strengthens or repairs wood jambs. Improves security with 3 in long screws attaching to wall stud.

190 deg viewer. Lenses projects 1/4 in from face of door. Four optical glass lenses, for doors 1-3/8 to 2-1/8 in thick. Installation requires 9/16 in hole, height 60 in from floor.

Protects interior or exterior door surface.

Brass keepers and steel chain secures door while allowing viewing and ventilation. Includes 1 chain lock with keeper and installation screws. Prefix U on factory number denotes new Defender Security packaging.

Protects interior or exterior door surface.

Reinforces and repairs door edge. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates lockset or deadbolt with any backset.

Protects out-swinging door from forced entry. Includes 1 shield, 2 carriage bolts, 2 cap nuts and washers.

Commercial door strike. Fits standard ASA cutout. 4-7/8 in x 1-1/4 in. Includes 1 strike and 1 set of installation screws.

The Shepherd Hardware Wall Protectors are used to to protect surfaces from door knob damage or cover existing damage. Self-adhesive and paintable circular disk.

Protects doors against forced entry, used on Out swinging doors with 2-3/8in standard residential backset, may be used on both hollow metal or wood doors.

Standard commercial 4-7/8 in strike. Used on wood or metal jambs with most grade 1 locksets. Fits standard ASA cutout. Includes 1 strike with two #12-24 x 1 in Phillips flat head combination screws.

Economy doorstop. Spring helps prevent wall damage. 3 in projection. Polybagged.

Covers 1/2 to 2-1/8 in holes. Helps maintain entry security. Fits doors up to 1-3/4 in thick.

Protects interior or exterior door surface.

Solid brass keepers with steel chain secures door while allowing viewing and ventilation. One 5/8 in x 2 in keeper and one 3-5/16 in x 1-3/8 in keeper. Prefix U on factory number denotes new Defender Security packaging.

Telescopic aluminum bar accommodates 28 in to 48 in wide inside and outside sliding patio doors. No cutting required. Includes 1 bar, locking saddle and installation screws.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets or deadbolts.

Designed to secure extra large or heavy doors. Large footprint grips on rough or uneven surfaces and large heel holds doors with clearances up to 2 in from floor surface.

Designed to secure extra large or heavy doors. Large footprint grips on rough or uneven surfaces and large heel holds doors with clearances up to 2 in from floor surface.

Designed to secure extra large or heavy doors. Large footprint grips on rough or uneven surfaces and large heel holds doors with clearances up to 1 in from floor surface.

Designed to secure extra large or heavy doors. Large footprint grips on rough or uneven surfaces and large heel holds doors with clearances up to 2 in from floor surface.

Arm length of 4 in. Rubber bottom for secure hold. Slim Pak, polybagged.

Deep cut and double action spring combine to assure ease of operation and auto holding of bolt projected or retracted. Packed with screws. 1/2 in Dia bolt head, 1 in throw. Polished solid brass faceplate and one piece aluminum rod and bolt. Specifically designed with face plate rounded for simple one-step router installation. O.A Size of 6 in L x 3/4 in W x 1-5/16 in D. Polybagged.

Designed for screen doors. Polybagged, slim pack.

Protects out-swinging door from forced entry. Includes 1 shield, 2 carriage bolts, 2 cap nuts and washers.

Protects interior or exterior door surface.

Pull size 5-1/4 in center to center.

For doors with threshold or undercut doors. Gray, non-marring rubber bumper. 1-1/4 in height. Slim pak, polybagged.

Protects interior or exterior door surface.

Dual adjustable ball catch with square corners in bright brass.

Reinforces and repairs doors. Assists in preventing forced entry. Use on wood or metal doors with mortise or drive-in latches. Accommodates key-in knob locksets or deadbolts.

The ProSource door closer body is constructed of cast aluminum with power size 2, built in non hold-open, plastic cover and it's a surface mount residential door closer. It Includes standard Arm. The arm opening angle is 180 deg.

Steel keepers and steel chain secures door while allowing viewing and ventilation. Includes 1 chain lock with keeper and installation screws. Prefix U on factory number denotes new Defender Security packaging.

Use on out-swinging doors with 2-3/8 in standard residential backset. Protects against forced entry. Includes 1 shield, 2 carriage bolts and 2 cap nuts and washers.

Plated steel strike is supplied with 3 in long wood screws to allow additional security, by fastening thru jamb into 2 x 4 outer door framing. 1-5/8 in W x 11 in H. Spacing between deadbolt opening and latch opening of 3-5/8 in.

Supplied with 3 in long wood screws to allow additional security by fastening thru jamb into 2 x 4 outer door framing. Replaces standard strikes and provides improved security.

Adjustable ball catch in bright brass.

Slide bolt surface mounts to face of door. Two keepers allow for surface or mortise frame installation. Includes one 1-1/4 in surface keeper and one 9/16 in x 1-5/8 in mortise keeper. Prefix U on factory number denotes new Defender Security packaging.

Slide bolt surface mounts to face of door. Two keepers allow for surface or mortise frame installation. Includes one 1-1/4 in surface keeper and one 9/16 in x 1-5/8 in mortise keeper. Prefix U on factory number denotes new Defender Security packaging.

The ProSource door closer body is constructed of cast aluminum with power size 2, built in non hold-open, plastic cover and it's a surface mount residential door closer. It Includes standard Arm. The arm opening angle is 180 deg.

The ProSource door closer has an aluminum die-cast body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The compact size with decorative finished cover suits most interior and exterior applications. The door closer has a hold-open feature.

The ProSource door closer has an aluminum die-cast body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The compact size with decorative finished cover suits most interior and exterior applications. The door closer has a hold-open feature.

The ProSource door closer has an aluminum die-cast body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The compact size with decorative finished cover suits most interior and exterior applications. The door closer has a hold-open feature.

The ProSource door closer has an aluminum die-cast body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The compact size with decorative finished cover suits most interior and exterior applications. The door closer has a hold-open feature.

The ProSource door closer has an aluminum die-cast body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The compact size with decorative finished cover suits most interior and exterior applications. The door closer has a hold-open feature.

The ProSource door closer has an aluminum die-cast body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The compact size with decorative finished cover suits most interior and exterior applications. The door closer has a hold-open feature.

The ProSource door closer has an aluminum casted body with steel arm to resist corrosion. It's steel rack and pinion is heat treated for smooth action and minimum wear. The closer is lubricated with stable hydraulic fluid for multi-climate operation. It has an adjustable back check, fits left handed or right handed installations, does not have hold-open feature and the power size is 1-4. This product is ADA compliant and it comes boxed.

Soft to protect wall opposite door knobs. Prop 65 Warning: This product may contain a chemical known to the State of California to cause cancer or birth defects or other reproductive harm.

Doorstop is held in place by hinge pin. Helps prevent wall damage. Adjustable to stop door at any angle. Self-adjusting pad makes full contact with door. Polybagged.

Protects interior or exterior door surface.

Slide bolt surface mounts to face of door. Two keepers allow for surface or mortise frame installation. Includes one 1-1/4 in surface keeper and one 9/16 in x 1-5/8 in mortise keeper. Prefix U on factory number denotes new Defender Security packaging.

Securely locks patio door in closed or ventilating position by preventing sliding and lifting. 2-3/8 in L x 3/16 in OD case hardened steel pin locks in retaining ring when engaged and stores in holder when unlocked. Includes pin with chain, retaining cap, holder and installation screws.

Protects interior or exterior door surface.

Protects interior or exterior door surface.